Effect of combined flexion and external rotation on measurements of the proximal femur from anteroposterior pelvic radiographs - 11/06/18
Bienvenido a EM-consulte, la referencia de los profesionales de la salud.
Artículo gratuito.
Conéctese para beneficiarse!
Abstract |
Introduction |
Fixed flexion and external rotation contractures are common in patients with hip osteoarthritis and, in particular, before total hip replacement (THR). We aimed to answer the following question: how does combined flexion and external rotation of the femur influence the radiographic assessment of (1) femoral offset (FO) (2) neck-shaft angle (NSA) and (3) distance (parallel to the femoral axis) from greater trochanter to femoral head center (GT-FHC)?
Hypothesis |
Combined flexion and external rotation impact the accuracy of two-dimensional (2D) proximal femur measurements.
Materials and methods |
Three-dimensional (3D) CT segmentations of the right femur from 30 male and 42 female subjects were acquired and used to build a statistical shape model. A cohort (n=100; M:F=50:50) of shapes was generated using the model. Each 3D femur was subjected to external rotation (0°–50°) followed by flexion (0°–50°) in 10° increments. Simulated radiographs of each femur in these orientations were produced. Measurements of FO, NSA and GT-FHC were automatically taken on the 2D images.
Results |
Combined rotations influenced the measurement of FO (p<0.05), NSA (p<0.001), and GT-FHC (p<0.001). Femoral offset was affected predominantly by external rotation (19.8±2.6mm [12.2 to 26.1mm] underestimated at 50°); added flexion in combined rotations only slightly impacted measurement error (20.7±3.1mm [13.2 to 28.8mm] underestimated at 50° combined). Neck-shaft angle was reduced with flexion when external rotation was low (9.5±2.1° [4.4 to 14.2°] underestimated at 0° external and 50° flexion) and increased with flexion when external rotation was high (24.4±3.9° [15.7 to 31.9°] overestimated at 50° external and 50° flexion). Femoral head center was above GT by 17.0±3.4mm [3.9 to 22.1mm] at 50° external and 50° flexion. In contrast, in neutral rotation, FHC was 12.2±3.4mm [3.9 to 22.1mm] below GT.
Discussion |
This investigation adds to current understanding of the effect of femoral orientation on preoperative planning measurements through the study of combined rotations (as opposed to single-axis). Planning measurements are shown to be significantly affected by flexion, external rotation, and their interaction.
Level of evidence |
IV Biomechanical study.
El texto completo de este artículo está disponible en PDF.Keywords : Femoral orientation, Preoperative planning, Femoral offset, Neck-shaft angle
Esquema
| ☆ | Presented to Closed Meeting International Hip Society, London September 2017. |
Vol 104 - N° 4
P. 449-454 - juin 2018 Regresar al número
Artículo precedente
- Impact of operative time on early joint infection and deep vein thrombosis in primary total hip arthroplasty
- B.W. Wills, E.D. Sheppard, W.R. Smith, J.R. Staggers, P. Li, A. Shah, S.R. Lee, S.M. Naranje
- Total hip arthroplasty after a previous pelvic osteotomy: A systematic review and meta-analysis
- T. Shigemura, Y. Yamamoto, Y. Murata, T. Sato, R. Tsuchiya, Y. Wada
Bienvenido a EM-consulte, la referencia de los profesionales de la salud.